GEOMETRIC PARAMETERS AND WEAR RESISTANCE OF CAM PROFILE OF A GAS DISTRIBUTION SHAFT

Ciulli E., Piccigallo B., Vela D. Experimental study of engine cam-followers. Proceedings of the XIX Congresso AIMETA. Ancona, 2009, September 14-17. Aras Edizioni, Fano, 2009, p. 10. ISBN 978- 88-96378-08-3.

Lindholm P. et al., Test equipment for a cam and follower system in a diesel engine. Proceedings of the OST-2001 Symposium on Machine Design. Tallin, Estonia, 2001.

Mohd H. Gh. Finite element analysis of cam and its follower contact stress mechanism, Cambridge, 2007, October, vol. 148.

Paradorn V. An impact model for the industrial cam-follower system: simulation and experiment. Chicago, 2007, October 11.

Kushwaha M., Rahnejat H. Transient elastohydrodynamic lubrication of finite line conjuction of cam to follower concentrated contact. Physics D: Applied Physics, 2002, vol. 35, pp. 2872–2890.

Kano M. Super low friction of DLC applied to engine cam follower lubricated with estercontaining oil. Tribology International, 2006, no. 39, pp. 1682–1685.

Hua D.Y., Farhang K., Seitzman L.E. A multi-scale system analysis and verification for improved contact fatigue life cycle of a cam-roller system. Tribology-ASME, 2007, vol. 129, pp. 321–325.

Glovnea R.P., Spikes H.A. The influence of cam-follower motion on elastohydrodynamic film thickness. Proceedings of the 27th Leeds-Lyon Symposium on Tribology. Amsterdam, Elsevier, 2001, pp. 485–493.

Irgashev A. Methodological bases of increasing the wear resistance of gears of heavily loaded gear transmissions of machine units. Doctor’s degree dissertation. Tashkent, 2005, 244 p.

Vela D., Ciulli E., Piccigallo B. Wear and elastohydrodynamic lubrication studies of cams and followers. Proceedings of the 2nd European Conference on Tribology (ECOTRIB 2009). Pisa, Italy, 2009, June 7-10. Pisa, Edizioni ETS, 2009, vol. 2, pp. 957–962. ISBN 978-884672426-7.

Kitahara T. Improvement of lubrication for cam and follower. Tribology Transactions, 1999, vol. 42, no. 4, pp. 755–762.

Irgashev B.A., Zhumanov R.M. Conussimon rollikli bearing elementlarinigi eilishbardoshligi. Ilm-fan va innovatsionniyu rivozhlanish – Science and innovative development, 2022, no. 4, p. 55.

Hugnell A.B-J., Bjorklund S., Andersson S. Simulation of the mild wear in a cam-follower contact with follower rotation. Wear, 1996, vol. 199, pp. 202–210.

Xuesong M., Youbai X. A numerical analysis of the non-steady EHL process in highspeedrotating engine cam/tappet pairs. Tribology-ASME, 1996, vol. 118, pp. 637–643.

Soejima M., Ejima Y., Wakuri Y., Kitahara T. Improvement of lubrication for cam and follower. Tribology Transactions, 1999, vol. 42, no. 4, pp. 755–762.

Vasiliev A.V., Grigoriev E.A. Profiling of gas distribution cams of internal combustion engines with improved hydrodynamic lubrication conditions. Engines Engineering, 1999, no. 1, pp. 25–28.

Stepurin P.V. Theoretical study of friction and wear of working surfaces of cam mechanisms. Friction and wear, 1998, vol. 19, no. 6, pp. 739–744.

Ikramov U.A., Irgashev A., Makhkamov K.H. Calculation model to assess the wear resistance of gears by concentrations of wear products in oil. Friction and wear, 2003, vol. 24, no. 6, pp. 620–625.

Irgashev A., Irgashev B.A. Wear resistance of gears. Tashkent, Tashkent State Technical University, 2013, 165 p.

Irgashev A.I., Mirzaev K.K., Irgashev B.A. Increasing wear resistance of gears. Tashkent, Tashkent State Technical University, 2015, 175 p.