METHODOLOGY FOR DETERMINING THE PRODUCTIVITY OF EXCAVATORS WHEN EXPLOITING AN INCLINED CROSS-MOUNTED COUPLING COAL OPEN

Admin bo'lib kirish (www.admin.slib.uz)

Tizim sinov (TEST) rejimida ishlamoqda! Murojat uchun @slib_support

Eski talqinga o'tish link

20 октябр 2020

Asosiy til:Ingliz

METHODOLOGY FOR DETERMINING THE PRODUCTIVITY OF EXCAVATORS WHEN EXPLOITING AN INCLINED CROSS-MOUNTED COUPLING COAL OPEN

Fan yo'nalishi:

5f8e70d8da576.pdf

PDF

Technical science and innovation

Maqola chop etish see more

MAQOLA ANNOTATSIYASI

This article provides a methodology for determining the time of mining and productivity of an excavator when developing an inclined exit ledge of coal mines. The working time of the exit ledge was calculated and the average operational productivity of the excavator in the Angren coal mine was determined. The technological scheme of working out benches by longitudinal runs of a mobile excavator-crushing complex with a lateral location of the downhole conveyor and the presence of a mobile interstage loading crane with sequential mining operations at two horizons is considered. According to this technological scheme, a methodology for determining the full working cycle of a complex is recommended. When calculating the operational productivity and operating time of the complex according to this technological scheme, all downtimes of the excavator are taken into account. At different bottom heights, the fill factor of the excavator bucket is determined taking into account the digging force of the excavator and the specific resistance to digging the rock. A mathematical model has been developed to determine the area of the excavator digging segment. For a more accurate calculation of the bottom, a mathematical model is used to determine the area of the excavator's digging segment with the establishment of chip thickness. The desired area is determined using the double integral. The dependence of the filling factor of the bucket of the excavator on the height of the face at various chip thicknesses is established.

MUALIFLAR

Teglar

# excavator-crushing complex# excavator productivity# inclined exit bench# working time

Maqolani baholang

0

0 ta

Maqola idintifikatorlari

ROI:

https://eroi.uz/11.0008/A1020-0011

DOI:

Mavjud emas

Foydalanilgan adabiyotlar

1. Nasirov U.F., Zairov Sh.Sh., Annakulov T.J. Primeneniye sxem siklichno-potochnoy texnologii s peredvijnymi i mobilnymi drobilno-peregruzochnymi kompleksami na otkrytyx gornyx rabotax // Nauchno-texnicheskiy i proizvodstvenny jurnal «Gorny Vestnik Uzbekistana». -Navoi, 2019. - № 2. -pp. 36÷39.

2. Zairov Sh.Sh., Annakulov T.J., Kuvondikov O.A., Sharipov L.O. Raschet texnologicheskix parametrov komplektov oborudovaniy mobilnyx drobilno-peregruzochno- konveyernyx kompleksov // Nauchno-texnicheskiy i proizvodstvenny jurnal «Gorny Vestnik Uzbekistana». -Navoi, 2019. - № 3. -pp. 29-34.

3. Faul A.A. Opredeleniye parametrov i pokazateley otkrytoy razrabotki mestorojdeniy nerudnyx stroitelnyx materialov s ispolzovaniyem mobilnyx drobilnyx kompleksov // Diss. ... kand. texn. nauk. - S.-Pb., 2012. - 193 p.

4. Annakulov T.J. Sovershenstvovaniye siklichno-potochnoy texnologii razrabotki vskrыshnыx porod v razreze Angrenskiy s primeneniyem mobilnыx kompleksov // «European Applied Sciences» ORT Publishing. –Stuttgart, Gerмany, 2015. – №6. ‒ рр. 58-60.

5. Annakulov T.J. Intensifikatsiya siklichno-potochnoy texnologii s ispolzovaniyem mobilnyx kompleksov na ugolnyx mestorojdeniyax // Diss. ... dokt. filosofii po texnicheskim naukam. -Navoiy, 2019. - 120 p.

6. Dombrovskiy N.G. Ekskavatory. Obshiye voprosy teorii, proyektirovaniya, issledovaniya i primeneniya. - M. : Mashinostroyeniye, 1969. - 319 p.

7. Frolov K.V., Ksenevich I.P., Volkov L.A., Karasev G.N. i dr. Ensiklopediya po mashinostroyeniyu. Tom IV. - M.: Mashinostroyeniye, 2005. - 736 p.

8. Poderni R.Yu. Mexanicheskoye oborudovaniye karyerov. Uchebnik dlya vuzov. - M.: Izd-vo MGGU, 2003. - 606 p.

9. Usmanov N.S., Soy I.V., Irkabayev U.U., Nasriddinov I.X., Annakulov T.J. Opyt vnedreniya siklichno-potochnoy texnologii na vskryshnom komplekse razreza Angrenskiy // Gorny vestnik Uzbekistana. - Navoi, 2015. - №1. - pp. 82-86.

Annakulov T.J., ZairovSh.Sh., Kuvandikov O.A. Justification, selection and calculation of technological parameters of equipment kits of mobile crushing-reloading-conveyor complexes // International Journal Of Advanced Research in Science, Engineering and Technology.– India: National Institute of Science Communication and Information Resources, 2019, Fevruiary. ‒ Vol.6. ‒ Issue 2. ‒ pp. 8072-8079.

11. Annakulov T.J. Razrabotka texnologicheskix sxem otkrytoy razrabotki mestorojdeniy s ispolzovaniyem mobilnyx kompleksov // Materialy XXIV Mejdunarodnoy nauchno-prakticheskoy konferensii na temu: «Innovatsiya-2019». - Tashkent: TashGTU, 2019. ‒ pp. 192-194.

12. Mohammad Reza Tavakoli Mohammadi, Seyed Ahmad Hashemi, Farhad Moosakazemi. Review of the in-pit crushing and conveying (IPCC) system and its case study in copper industry https://www.researchgate.net/publication/270888181.