An analysis of literary data on the use of multi-motor electric drives for
overhead crane movement mechanisms shows that new types of hoisting mechanisms
and automated hoisting and transport systems being created determine new, higher
requirements for cranes and their control systems. An electric drive control system
should be understood as a complex consisting of an electrical energy converter (if any),
control equipment for switching current in the electric motor circuit, manual control or
automatic (software) control, high-speed or other control, as well as protection elements
for electrical equipment and mechanism, ultimately acting on the drive disconnection
devices. Crane control systems are classified as devices that are under the continuous
control of the operator, that is in these systems, the moment of inertia, speed
parameters and the moment of completion of the operation are selected by the person
controlling this mechanism. The control system, in turn, must provide the necessary
switching sequence to implement the desired speed parameters, as well as prevent, at
the same time, unacceptable overloads and provide the necessary protection. In the
crane electric drive, the direct control system using power cam controllers is most
widely used. It is characterized by the greatest ease of management and maintenance.
Cam controllers with different circuits, depending on their purpose, control DC motors.
For lifting mechanisms, an asymmetric controller circuit is used with potentiometric
switching on of the motor armature in the descent positions, and for movement
mechanisms, a symmetrical controller circuit with resistors switched off in series. With
alternating current, cam controllers are used to control single-speed asynchronous
squirrel-cage and phase rotor motors. In the first case, the controller performs the
functions of turning on and off the squirrel-cage motor without regulating its speed: in
the second case, switching the stator windings, as well as the stages of resistors in the
rotor circuit.
An analysis of literary data on the use of multi-motor electric drives for
overhead crane movement mechanisms shows that new types of hoisting mechanisms
and automated hoisting and transport systems being created determine new, higher
requirements for cranes and their control systems. An electric drive control system
should be understood as a complex consisting of an electrical energy converter (if any),
control equipment for switching current in the electric motor circuit, manual control or
automatic (software) control, high-speed or other control, as well as protection elements
for electrical equipment and mechanism, ultimately acting on the drive disconnection
devices. Crane control systems are classified as devices that are under the continuous
control of the operator, that is in these systems, the moment of inertia, speed
parameters and the moment of completion of the operation are selected by the person
controlling this mechanism. The control system, in turn, must provide the necessary
switching sequence to implement the desired speed parameters, as well as prevent, at
the same time, unacceptable overloads and provide the necessary protection. In the
crane electric drive, the direct control system using power cam controllers is most
widely used. It is characterized by the greatest ease of management and maintenance.
Cam controllers with different circuits, depending on their purpose, control DC motors.
For lifting mechanisms, an asymmetric controller circuit is used with potentiometric
switching on of the motor armature in the descent positions, and for movement
mechanisms, a symmetrical controller circuit with resistors switched off in series. With
alternating current, cam controllers are used to control single-speed asynchronous
squirrel-cage and phase rotor motors. In the first case, the controller performs the
functions of turning on and off the squirrel-cage motor without regulating its speed: in
the second case, switching the stator windings, as well as the stages of resistors in the
rotor circuit.
| № | Муаллифнинг исми | Лавозими | Ташкилот номи |
|---|---|---|---|
| 1 | Abidov K.G. | teacher | TSTU |
| 2 | Dadadjanov K.S. | teacher | TSTU |
| № | Ҳавола номи |
|---|---|
| 1 | “On measures for the further introduction of modern energy-efficient and energysaving technologies”. “Decree of the President of the Republic of Uzbekistan dated”. 2017. 32 |
| 2 | K.R. Allaev. Modern energy and prospects for its development. “Under the general editorship of Academician”. 2021. 952 |
| 3 | K.R. Allaev. “Energy of the world and Uzbekistan. Analytical review”. 2006. 380 |
| 4 | I.I. Dubinsky, O.I. Katselson. “Application of IR for starting IM with a phase rotor Prom energetics”. 1971 |
| 5 | N.M. Usmankhodzhaev, K.S. Dadadjanov. Coordination of the speeds of electric motors in the mechanisms of movement of overhead cranes. “Journal, hoisting and transport equipment and warehouses”. 1992. 15 |
| 6 | L.R. Neiman. Surface effect in ferromagnetic bodies. “Publishing House”. 1949. 190 |
| 7 | K.S. Demirchina Calculation and modeling of electrical devices taking into account the surface effect. “Proceedings of LPI”. 1986. 152 |
| 8 | S.I. Petrov. “Theoretical foundations of electrical engineering. established and transitional”. 2006 |
| 9 | V.A. Pryanishnikov. “Electrical engineering and TOE in examples and tasks, practical”. 2004 |
| 10 | V.A. Pryanishnikov, E.A. Petrov, Y.M. Osipov. “St. Petersburg: Korona print”. 2003. 334 |
| 11 | M.P. Belov, V.A. Novikov, L.N. Rassudov. Automated electric drive of typical production mechanisms and technological complexes. “A textbook for universities. Academy”. 2004. 576 |
| 12 | S.V. Gavrilova, I.A. Sokolova, V.I. Domanov. Mathematical modeling of a multimotor electric drive Automation and Instrumentation: Problems, Solutions: Mat. intl. scientific and technical conf.; scientific. “Publishing House”. 2017. 63 |
| 13 | N.M. Usmankhodzhaev, M. Kadyrov. “On the method of calculating IR in the system of coordinated rotation of synchronous motors based on the principle of an electromagnetic working shaft. USSR Electromechanics”. 1991. 23 |
| 14 | I.M. Usmankhodzhaev, P.I. Sagitov. The system of coordinated rotation of asynchronous motors. “Electrical Engineering”. 1976. 46 |
| 15 | A.A. Usoltsev. Vector control of asynchronous motors: textbook. allowance. - St. Petersburg: Publishing House. “State Institute of Fine Mechanics and Optics”. 2002. 55 |
| 16 | M.G. Chilikin, V.I. Klyuchev, A.S. Sandler. “Theory of automated electric drive energies”. 1979. 614 |
| 17 | R.T. Schreiner. “Mathematical modeling of AC electric drives with semiconductor frequency converters”. 2000. 654 |
| 18 | A.G. Yaure, E.M. Pevzner, V.N. Tishchenko. Construction of asynchronous multimotor electric drives for mechanisms of movement of cranes with electrical connection along the circuit of the rectified current of the rotor. “Electro technical”. 1981. 12 |