260

  • Internet havola
  • DOI
  • UzSCI tizimida yaratilgan sana 22-02-2021
  • O'qishlar soni 259
  • Nashr sanasi 26-10-2020
  • Asosiy tilIngliz
  • Sahifalar222-227
Kalit so'z
Ўзбек

This article discusses comparative analyzes of clearance control methods in a spur bevel gear. The traditional designs of bevel gear reducers provide the only possibility of adjusting the lateral clearance in the gearing by joint axial movements of both wheels. The clearance adjustment used in the assembly of a real transmission by axial displacements of the bevel wheels inevitably leads to a deterioration of the fit of the teeth, and it should be considered unacceptable. In a fully adjustable bevel gear with an adjustable design compensator in the form of a pair of rotary oblique washers, the clearance in the engagement is directly controlled by a change in the interaxal angle, which does not affect the quality of the tooth fit. The presence of the adjusting device and, accordingly, the compensation link in the dimension chain, which determines the accuracy of the angle between the axes of rotation of the bevel wheels, determines the transmission assembly by the compensation method.

№ Muallifning F.I.Sh. Lavozimi Tashkilot nomi
1 Mamasobirov U.M. 1Tashkent State Technical University,
2 Kovalevsky V.I. Doctor of Technical Sciences 2Kuban State University of Technology
№ Havola nomi
1 1. Bevel gear: A.S. 1446387 USSR: MKI F16/14.
2 2. Kovalevsky V.I., Kurganbekov M.M., Nigmatullaev S.I. Adjusting the lateral clearance in a bevel gear by changing the interaxle angle. // Improving the performance of composite materials, components and machines. Collection of scientific papers. - Publishing house of TashPI. - Tashkent, 1989.Р. 28 - 34.
3 3. Dunaev P.F., Lelikov O.P. Calculation of dimensional tolerances. - M.: Mechanical Engineering, 1981. - 189 p.
4 4. Methods of effective regulation and rational design of spur bevel gears. / Ayrapetov E.L., Kovalevsky V.I., Kuban. state technol. univ - Krasnodar, 2002.– 88 p., Ill. Bibliogr. 37 title: Rus. - Dep. at VINITI,. 10.30.02,. №1868.V 2002.
5 5. Kanatnikov N.V. Povishenie effektivnosti obrabotki konicheskix zubchatix koles srednego modulya. [Tekst] / N.V. Kanatnikov, A.A. Revenkov // Fundamentalnie i prikladnie problemi texniki i texnologii, 2012. №3/3(293). S.24-33.
6 6. Kanatnikov N.V. Vozmojnosti povisheniya proizvoditelnosti protsessa zubostroganiya konicheskix zubchatix koles. [Tekst] / A.V. Kanatnikov, N.V. Kanatnikov, G.A. Xarlamov, // «Aktualnie problemi texniki i texnologii mashinostroitelnogo proizvodstva». Materiali VI Vserossiyskoy nauchno-texnicheskoy konferensii. - Orel: UNPK, 2013 S.30-32.
7 7. Lagutin S.A. Sochetanie prodolnoy i profilnoy modifikatsy zubev v silindri-cheskix peredachax // Konversiya v mashinostroenii. 2001. № 2. S. 68–72.
8 8. Shalobaev E.V., Medunetskiy V.M., Monaxov YU.S. Geometricheskaya optimizatsiya tribo-pari v zatseplenii zubchatix koles // Sbornik dokladov nauchno-texn. konf. s mejdunar. ucha-stiem «Teoriya i praktika zubchatix peredach», Ijevsk: IjGUT, 2004.S. 139-144.
9 9. Trubachev E.S. Osnovi analiza i sinteza zatsepleniya realnix spiroidnix peredach: diss…dokt. texn. nauk, Ijevsk, 2004. -347 s. (nauchniy konsultant prof. V.I. Goldfarb).
10 10. Ivanov M.N. Detali mashin: Uchebnoe posobie dlya mashinostroitelnix spetsialnostey vuzov/M.N. Ivanov, V.A. Finagenov. – 11-e izd., pererab. – M.: Vissh. SHk., 2007. – 408 s.
11 11. Lopatin B.A. Formirovanie vnutrennego priblijennogo zatsepleniya silindro-konicheskix peredach / B.A. Lopatin, E.A. Poluektov, S.A. Xaustov // Vestnik YUUrGU. Seriya «Mashinostroenie».- 2011.№ 17.S. 39-48.
12 12. Timofeev B.P. Standartizatsiya parametrov tochnosti zubchatix koles i peredach. // Aktualnie zadachi mashinovedeniya, detaley mashin i tribotexniki: trudi Mejdunarodnoy nauchno-texnicheskoy konferensii, 27-28 aprelya 2010 g. / Balt. Gos. Texn. Un-t. – SPb., 2010.S. 10-14.
13 13. Timofeev B.P., Abramchuk M.V. O protivorechy v normirovany bokovogo zazora v otechestvennom standarte GOST 1643-81. // Problemi tochnosti v mexanike i priborostroenii // Sbornik tezisov VIII Vserossiyskoy mejvuzovskoy konferensy molodix uchenix. Vipusk 2. / Glavniy redaktor d.t.n., prof. V.O. Nikiforov. – SPb: SPbGU ITMO, 2011. S. 256-258.
14 14. Sheveleva G.I., Volkov A.E., Medvedev V.N. Sravnenie metodov rascheta kontaktnix davleniy v konicheskix peredachax s krugovimi zubyami. Vestnik mashinostroeniya, 2003. № 6. S. 9–12.
15 15. Shtripling L.O., Xromix A.S. Ob’emnoe proektirovanie protsessov izgotovleniya i kontrolya konicheskix peredach s krugovimi zubyami // Problemi mexaniki sovremennix mashin: Mat. II Mejdunar. konf.Ulan-Ude, 2003. T. 3.S. 97–100.
16 16. Vorobev YU.V., Kovergin A.D. Proektirovanie zubchatix peredach na dolgovechnost s uchetom treniya // Vestnik TGTU, 2004. T. 10 .№ 16. S. 205–211.
Kutilmoqda